Thin-disk Lasers | |
The thin-disk laser (sometimes called thin-disc laser or active-mirror laser) is a special kind of diode-pumpedhigh-power solid-state laser, which was introduced in the 1990s by the group of Adolf Giesen at the University of Stuttgart, Germany. The main difference from conventional rod lasers or slab lasers is the geometry of the gain medium: the laser crystal is a thin disk, where the thickness is considerably smaller than the laser beam diameter, so that the heat generated is extracted dominantly through one end face, i.e., in the longitudinal rather than in the transverse direction. The cooled end face has a dielectric coating which reflects both the laser radiation and the pump radiation.
Figure 1: Setup of an 8-kW laser based on four thin-disk laser heads (seen on the left side). The photograph was kindly provided by TRUMPF.
The thin disk is also often called an active mirror [1], because it acts as a mirror with laser gain. Within the laser resonator, it can act as an end mirror or as a folding mirror. In the latter case, there are two double passes of the laser radiation per resonator round trip, so that the gain per round trip is doubled and the threshold pump power is reduced.
Figure 2: Schematic setup of a thin disk laser head. The pump optics (not shown) are arranged for multiple passes of the pump radiation. The heat is extracted in the longitudinal direction, which minimizes thermal lensing effects.
The thin-disk laser should not be confused with the rotary disk laser, where the gain medium is a quickly rotating disk, which is usually a few millimeters thick.
Reduced Thermal Issues at High Output Powers; Power Scalability
Due to the small thickness of the disk (e.g. 100–200 μm for Yb:YAG), the temperature rise associated with the dissipated power is small. In addition, the temperature gradients are dominantly in a direction perpendicular to the disk surface and thus cause only weak thermal lensing and depolarization loss. This allows for operation with very high beam quality due to the weak thermal beam distortions, and stable operation can be achieved over a wide range of pump powers.
A very important property arising from the thin-disk geometry is power scalability in a strict and meaningful sense. The scaling procedure is simple: for example, the output power can be doubled by applying twice the pump power to twice the area on the disk, while keeping the disk thickness and doping level constant. The laser resonator has to be modified so as to double the mode area in the disk. With this scaling procedure applied, the new design with twice the output power has unchanged peak optical intensities and a nearly unchanged maximum temperature in the disk (the latter basically because the cooling area has also been doubled). As far as thermal lensing results from the temperature dependence of the refractive index, the dioptric power (inverse focal length) of the thermal lens is reduced to half of the original value, which just compensates the doubled sensitivity of the larger mode to focal length changes. The power has thus been scaled without increasing optical intensities, the magnitude of temperature rises, or thermal lens problems. Strictly, thermal lensing effects can be increased by the power scaling as far as they result from mechanical stress in the disk, but this problem can be kept small by keeping the disk thickness small. Another limitation arises from amplified spontaneous emission (ASE) in the transverse direction, which ultimately limits the gain achievable in the longitudinal direction, but becomes severe only at very high power levels with many kilowatts from a single disk. The use of a composite disk with an undoped part on top of the doped part can also strongly suppress ASE; at least for continuous-wave lasers, the ASE limit may be pushed to the order of 1 MW from a single disk.
Power scalability in a wide range is achieved even for passively mode-locked thin-disk lasers (see below). Here, the doubling of the output power also involves doubling of the mode area on the SESAM, so that optical intensities in that device and also cooling issues are – contrary to naïve expectations – not limiting factors. Limitations rather arise from the problem of doing dispersion compensation at high power levels.
So far, hundreds of watts of output power in a diffraction-limited continuous-wave beam have been obtained. By using multiple thin-disk laser heads within one laser resonator, several kilowatts of power can be generated; thin-disk lasers with 8 kW output power in a multimode beam are commercially available, and similar or even higher power levels in nearly diffraction-limited beam will be realized in the near future. With mode-locked thin-disk lasers, ∼ 80 W of average output power has been achieved.
Multipass Pumping
The small thickness of the disk typically leads to inefficient pump absorption when only a single or double pass is used. This problem is normally solved by using a multi-pass pump arrangement, which can be made fairly compact when using a well-designed optical setup, typically containing a parabolic mirror and prism retroreflectors. Such arrangements easily allow one to arrange for e.g. 8 or 16 double passes of the pump radiation through the disk without excessively stringent requirements on the pump beam quality.
The pump source of a thin-disk laser is usually based on high-power diode bars, either in fiber-coupled form or with free-space power delivery. A typical pump wavelength is 940 nm for Yb:YAG, whereas ytterbium-doped tungstate crystals can be more efficiently pumped near 981 nm.
Thin-Disk Gain Media
The most often used gain medium for thin-disk lasers is Yb:YAG. Compared with Nd:YAG, it has a shorter emission wavelength (typically 1030 nm), a smaller quantum defect (reducing the dissipated power), a longer upper-state lifetime (improving energy storage for Q switching), and a larger gain bandwidth (e.g. for shorter pulses with mode locking). On the other hand, it is a quasi-three-level gain medium with significant reabsorption at the laser wavelength, and thus requires higher pump intensities. The thin-disk principle is well adapted to these parameters.
For broad wavelength tuning and for ultrashort pulse generation, other ytterbium-doped gain media offer a still wider gain bandwidth. Examples are tungstate crystals (Yb:KGW, Yb:KYW, Yb:KLuW), Yb:LaSc3(BO3)44 (Yb:CALGO) and Yb:YVO4. (Yb:LSB), Yb:CaGdAlO
Nd:YAG or Nd:YVO4 may also be used in thin-disk lasers, e.g. when a wavelength of 1064 nm is required, or when the much smaller saturation energy of Nd:YVO4 is relevant.
Spatial Hole Burning
An interesting consequence of the small disk thickness is that spatial hole burning usually cannot be avoided, even if a thin-disk laser is built with a ring resonator. (Note that due to the small ratio of thickness and beam radius, counterpropagating waves in the disk always have a strong overlap, so that an interference pattern is generated even in a ring resonator.) Nevertheless, single-frequency operation is possible by using an appropriate wavelength filter (etalon) in the resonator. For passive mode locking (see below), spatial hole burning in the thin disk distorts the shape of the gain spectrum, causing a variety of instabilities, but also allowing for significantly shorter pulses in the optimum range of parameters [5].
Q-switched Pulse Generation
Thin-disk lasers are well suited for generating high-energy nanosecond pulses with high beam quality, as required for, e.g., some kinds of laser material processing. The typically used gain medium Yb:YAG offers a significantly better energy storage (longer upper-state lifetime) compared with, e.g., Nd:YAG. A somewhat limiting factor, however, is the moderate gain (compared with that of an end-pumped bulk laser), which makes it difficult to achieve very short (few-nanosecond) pulses.
Mode-locked High-power Thin Disk Lasers
Thin-disk lasers are particularly attractive for the generation of ultrashort pulses at very high power levels. In addition to the high-power capability, the main advantages in this context are
- the ease of achieving diffraction-limited operation (which is a prerequisite for mode locking)
- the broad gain bandwidth of Yb:YAG (the so far most suitable gain medium for thin-disk lasers)
- the small nonlinearity of a thin disk, which helps to avoid excessive nonlinear phase shifts despite the high intracavity peak intensities
One of the initial challenges was to find a suitable mode-locking mechanism. Even though originally it was widely believed that passive mode locking with semiconductor saturable absorber mirrors (SESAMs) would not be possible at very high power levels – at least not without first developing special high-power SESAMs, possibly based on improved semiconductor materials –, the author's research group at ETH Zürich demonstrated around 2000 that both thermal and non-thermal issues can be relatively easily managed even at very high power levels, if only the design parameters of the overall laser system (and not only of the SESAM) are properly chosen. In other words, SESAM damage then does not constitute a limiting factor for the power scaling of mode-locked thin-disk lasers; in fact, it was found that the mode-locked thin-disk laser is the first truly power-scalable femtosecond laser. However, the design of such lasers involves a number of subtle issues, related to e.g. spatial hole burningdispersion compensation, and a trial-and-error approach not based on a solid understanding of various details is prone to fail, e.g. by not managing to suppress certain types of instabilities. and to
So far, thin-disk lasers have lead to the highest average output power of 80 W from a mode-locked laser [8, 10], and pulse energies of > 10 μJ combined with sub-picosecond pulse durations are possible [19, 20]. While typical pulse durations with Yb:YAG are around 700–800 fs, significantly shorter pulses are possible, e.g. with ytterbium-doped tungstate crystals such as Yb:KGW or Yb:KYW [7].
Amplifiers for High Pulse Energies
Thin-disk laser heads can also be used for regenerative amplifiers [11]. The relatively small gain of the thin disk can be compensated with a larger number of resonator round trips, even though this makes the amplifier more sensitive to optical losses and nonlinearities. Therefore, it can be advantageous to arrange for multiple passes of the signal radiation through the disk in each resonator round trip.
It is also possible to construct a purely multipass amplifier (without a resonator and optical switch), but this approach limits the overall gain and requires a carefully optimized setup in order to preserve a high beam quality.
Nonlinear Frequency Conversion
High-power continuous-wave green lasers can be easily realized in the form of intracavity frequency-doubledoptical parametric oscillators, amplifiers and generators [6]. A high-power RGB source based on a mode-locked thin-disk laser has also been demonstrated [10]. The high peak power of mode-locked thin-disk lasers allows for efficient nonlinear frequency conversion with critical phase matching in LBO crystals, thus not requiring crystal ovens for most or all conversion stages. thin-disk lasers. For Q-switched or mode-locked lasers, extracavity doubling is often more practical. Thin-disk lasers are also very interesting pump sources for
Further Development of the Thin-Disk Concept
The thin-disk laser concept allows for further variations. For example, side pumping of the disk may allow for even higher output powers while reducing the requirements on the pump beam quality. This approach, developed at the Lawrence Livermore National Laboratory, is based on a composite laser crystal [22]. An undoped YAG disk, which is bonded to a Yb:YAG disk, brings various benefits: It reduces the beam quality requirements for the pump source, reduces the tendency for transverse amplified spontaneous emission (ASE) and parasitic lasing in large disks, increases the mechanical strength and may improve the cooling. The side-pumped concept may thus allow scaling to much higher powers, even though not necessarily with diffraction-limited beam quality. An interesting option is to use a composite ceramic gain medium which is ytterbium doped only in the center region and not in the outside regions, which are used only to deliver the pump power.
It is also interesting to develop cryogenic thin-disk lasers, as cryogenic cooling greatly reduces thermal effects at high power levels.
Competition with Fiber Lasers
Thin-disk lasers are currently facing fierce competition from high-power fiber lasers and amplifiers. In continuous-wave operation, these can currently deliver even higher powers in close to diffraction-limited beams. However, they are generally considered to be still less mature for industrial applications. Within the next few years, both thin-disk lasers and fiber lasers are expected to show significant further progress, and it is currently not clear which technology will acquire the larger market share. See also the article on fiber lasers versus bulk lasers.
In the domain of ultrashort pulse generation, fiber amplifier systems allow one to reach even higher average powers and shorter pulse durations than thin-disk lasers can generate without amplification. However, thin-disk lasers will probably maintain superiority for the generation of pulses with high energies, particularly when high pulse quality (concerning temporal shape, low chirp, and stable linear polarization) is required. A key issue in this context is that both the small disk thickness and the larger beam diameter on the disk lead to a nonlinearity which is much smaller than that in a fiber laser resonator.
A detailed comparison of thin-disk versus fiber lasers is complex and has to take into account many aspects which depend on the particular application. For example, issues such as emission bandwidth, pulse quality and stability of polarization state can be essential in some cases but insignificant in others.
Semiconductor Disk Lasers
The thin-disk geometry is also used in vertical external cavity surface-emitting lasers (VECSELs), a kind of semiconductor lasers. In that case, multiple passes of the pump are usually not required due to the strong absorption of semiconductor materials. However, the concept with multiple pump passes has recently also been applied to such semiconductor lasers, where it allows for a reduced quantum defect and thus for reduced heating and potentially higher powers [12]. To date it is not clear whether this will lead to more efficient and practical lasers; tens of watts of output power have so far been reached with the original concept, not requiring multiple pump passes. Such lasers are actually very interesting, partly because they can be developed at different wavelengths, e.g. for blue light generation with intracavity frequency doubling at very high output power levels.
ليست هناك تعليقات:
إرسال تعليق